G-6000 spray adhesive strength, high solid content, non-stick fabric, tack to maintain a long time, from a small taste, the provincial environmental protection glue. The main purposes: mainly for high-end leather bags, sofa and toys, all kinds of crafts manufacturing, thermal performance is very good. Widely used in sofa, swivel chairs, screens, bags, mattresses, office desk, cabinets, air conditioning, leather, toys, paper and packaging industry; suitable for sponge, foam, fabric, leather, paper, wood, plastic, PVC , PE, EVA, metal, rubber, asbestos insulation, fire plate, aluminum plate and other materials and the need to work at high temperatures was a bonding adhesive products, using the airbrush gun has three parts: the gun, trachea, air pump (air compressor air) gun: general spray gun can, caliber 1.5-2.5MM, model R-71, W-77, F-75 majority. Recommended F-75, which bore diameter affordable, cheap. Pump: generalized selection split pump to pump head nameplate displacement sensitive. Each is equipped with a standard 1.2L displacement, select the size required to use the pump according to the number of guns such as: to simultaneously use three reports gun work, must be equipped with at least 3.0 or displacement pump trachea: and gun match for 8MM diameter of each pipe is not more than 30 meters. For longer distances, the diameter should be bold. Otherwise there are drop-side, the impact of spraying effect. 2, spray glue is first adjusted to 6-8 atm pressure. The glue guns equipped space alignment adjustments (see gun manual) to the amount transferred to the closest fog new glue-like, generally closed fan knob, it can be sprayed in a straight line and then align the material to a distance of 0.5 m from left to right, from far to near 20-degree angle to the way spraying Requirements propelled gun uniform, spraying lack of plastic, not rubber when spraying the product, not to spray more as well, want to spray both principles. 3, gun maintenance and cleaning pump: regular drainage, usually three days. Gun: keep the gun clean, spray glue and water mix are not a gun, it will run out of gun glue gun to exit the body. (Plastic cans can not pour) quit in two ways: A, remove plastic cans, spray directly on the body of glue finished, then attach the plastic cans. B, remove plastic cans with material blocked nozzle, operating gun, glue is automatically removed from the suction hose. If the glue gun back and blocking due to forgotten gun can be loaded thinner, white spray oil until smooth gun can be. Unloading, loading plastic tank Affairs hold necessary to open and close the lid, not directly hold the gun operation, so easy to damage the connecting nut between the tank and the gun (no nut on the market, damaged after a scrap Gun) (luggage manufacturing supplement spray application of) 4, material put off normally required materials placed with glue gluing placed as superimposed layers, revealing the need glue side. Because tack than powder spray glue, glue water to be strong, do not expose the material at the time of placing too much of the area, in order to be able to fully cover layer after folding its criteria. Such injustice can avoid unnecessary waste (to reduce the amount of one-third), mainly to avoid the process after the subbing layer exposed to cause trouble. Such as hemming car line, stick tram panel to feed the poor, such as walking. Small area and put the strip material: As the gun using compressed gas, easy to be swept away in a small area of ??material sprayed, maneuver. So you must spray a layer of glue on the table, and then paste the material neatly on the table before spraying. This glue has a sticker nature, countertops available after spraying once a working section, ie half a day. 5. After the folding plastic material without dim settings, 0-24 hours can be used, this glue tack Feng, long opening hours, do not touch each other glue level in the use and move to the same direction layer stacked house, pick up the order to use. Glue the proper use 六步曲 Step 1: Construction site open ventilation system, open doors and windows to ensure a well-ventilated spot; Step 2: pre-construction, check the gun is functioning properly, remove stagnant water pressure pipes; Step 3: Material Surface clean, without grease, dust or other impurities; Step 4: uniform spray nozzle facing surface of the material; linear: the nozzle surface of the material should be 45 ° angle; nozzle from the material surface to 0.5 meters or less is better; nozzle pressure should be transferred to 6-8kg (normal requirements)